Skip to main content

Nokia cell phone secrets codes

These Nokia codes will work on most Nokia Mobile Phones
  1. *3370# Activate Enhanced Full Rate Codec (EFR) - Your phone uses the best sound quality but talk time is reduced my approx. 5%
  2.  #3370# Deactivate Enhanced Full Rate Codec (EFR) OR *3370#
  3. *#4720# Activate Half Rate Codec - Your phone uses a lower quality sound but you should gain approx 30% more Talk Time.
  4. *#4720# Deactivate Half Rate Codec.
  5. *#0000# Displays your phones software version, 1st Line : Software Version, 2nd Line : Software Release Date, 3rd Line : Compression Type.
  6. *#9999# Phones software version if *#0000# does not work.
  7. *#06# For checking the International Mobile Equipment Identity (IMEI Number).
  8. #pw+1234567890+ 1# Provider Lock Status. (use the "*" button to obtain the "p,w"and "+" symbols).
  9. #pw+1234567890+ 2# Network Lock Status. (use the "*" button to obtain the "p,w"and "+" symbols).
  10. #pw+1234567890+ 3# Country Lock Status. (use the "*" button to obtain the "p,w"and "+" symbols).
  11. #pw+1234567890+ 4# SIM Card Lock Status. (use the "*" button to obtain the "p,w" Go to Topand "+" symbols).
  12. *#147# (vodafone) this lets you know who called you last.
  13. *#1471# Last call (Only vodofone).
  14. *#21# Allows you to check the number that "All Calls" are diverted to 
  15. *#2640# Displays security code in use.
  16. *#30# Lets you see the private number.
  17. *#43# Allows you to check the "Call Waiting" status of your phone.
  18.  *#61# Allows you to check the number that "On No Reply" calls are diverted to.
  19. *#62# Allows you to check the number that "Divert If Unreachable (no service)" calls are diverted to.
  20.  *#67# Allows you to check the number that "On Busy Calls" are diverted to.
  21.  *#67705646# Removes operator logo on 3310 & 3330.
  22.  *#73# Reset phone timers and game scores.
  23.  *#746025625# Displays the SIM Clock status, if your phone supports this power saving feature "SIM Clock Stop Allowed", it means you will get the best standby time possible.
  24.  *#7760# Manufactures code.
  25.  *#7780# Restore factory settings.
  26.  *#8110# Software version for the nokia 8110. Go to Top
  27.  *#92702689# Displays - 1.Serial Number, 2.Date Made, 3.Purchase Date, 4.Date of last repair (0000 for no repairs), 5.Transfer User Data. To exit this mode you need to switch your phone off then on again. ( Favourite )
  28.  *#94870345123456789 # Deactivate the PWM-Mem.
  29.  **21*number# Turn on "All Calls" diverting to the phone number entered.
  30. **61*number# Turn on "No Reply" diverting to the phone number entered.
  31.  **67*number# Turn on "On Busy" diverting to the phone number entered.
  32.  12345 This is the default security code. press and hold # Lets you switch between lines 
Labels:

Comments

Post a Comment

Popular posts from this blog

Ring tester

 In my Electronic repair job I found normal multimeter is somewhat limited  in certain area. so special tools are needed for saving  a lot of time  Ring tester is one of this kind .helping me to check small hi Q inductors SMPS transformer, TV Deflection coils ,LOT ,line driver transformer and almost any inductor working on hi frequency.Normal multimeter can only identify a open coil ,but not a shorted windings.  I found some commercial available ring tester. but it is not available in local shops of my area.also it seems priced high. So  I decided to make a ring tester of my own. Below is the one I successfully made from the junk box components. I found it very useful. and now it is one of my best test tool collection. Two Ic's, few LED's ,one plastic container and few resistors  made this wonderful tool. If we test it with primary of SMPS transformer or LOT windings of a good one shows all its LEDs will light. depending on the inductive reactantce  the number of LED 's
4 comments
Read more

Transistor numbers and codes

Most transistor markings follow one of these codes: JEDEC, JIS or Pro-Electron. For ICs, look for known numbers (e.g. 741, 4001, 7400) between the prefix and the suffix. Don't confuse it with the date code. ICs typically have two numbers: The part number and the date code. 1. Joint Electron Device Engineering Council (JEDEC) These part numbers take the form: digit, letter, sequential number, [suffix] The letter is always 'N', and the first digit is 1 for diodes, 2 for transistors, 3 for four-leaded devices, and so forth. But 4N and 5N are reserved for opto-couplers. The sequential numbers run from 100 to 9999 and indicate the approximate time the device was first made. If present, a suffix could indicate various things. For example, a 2N2222A is an enhanced version of a 2N2222. It has higher gain, frequency, and voltage ratings. Always check the data sheet. Examples: 1N914 (diode), 2N2222, 2N2222A, 2N904 (transistors). NOTE: When a metal-can version of a JEDEC tra
Post a Comment
Read more

Short Finder

  Today i made this Test instrument using Arduino ..very very usefull in find out shorted electronic components in mainboards.. espcially when lot of ICs sharing same power. if one componet get short the whole track shows 0 resistance when testing with normal multimeter.. its difficult to find which one is the dead rat.  Normally we need to take out each suspected component from board and need to test until we got the defective one.. its tedious job and damage the board.    Another way inject current to the circuit test the heat.. its not safe.   Here is the need of this device. When we trace the power line with this probe.. it gives high pitch audio tone when the probe near the particular shorted component.. It can test micro ohm resistance beyond normal meter range Automatically shut to save battery .if we forget to switch of the tester Auto calibration range. Portable The tester voltage and current safe to testing any components . On board testable.. Happy troubleshooting
Post a Comment
Read more